Luke Ingerman

The moment it all became real. From countless sleepless nights to the thrill of launch day — this was the moment we finally went live on Kickstarter. Watch as our founder reflects on the journey that brought the OTTOeject System to life. This isn’t just a project. It’s months of…

It's almost time for another Chat, Chill, N' Build Saturday edition. Grab your breakfast and coffee and join me for some more ZeroG Mercury building. I'm reprinting some parts now, but we will continue to prep and install electronics today at 10am ET. twitch.tv/DigitalDragon72

Chat, Chill, N’ Build stream will start at 7pm ET tonight. We will begin building the M34M1 toolhead so we can install the gantry belts. twitch.tv/DigitalDragon72

Dragon Den Pop Up Stream! Hey gang, come hangout as I build a toolhead and work though a BTT CB2 install on an BTT Manta M8P v1.0 board. twitch.tv/DigitalDragon72

It's Chat, Chill, N' Build Tuesday in the Dragon Den! We got some new linear rails in from @KB3D_Online for the ZeroG Mercury rebuild. Come join me at 6pm ET as we get the gantry and Z-Axis installed. twitch.tv/DigitalDragon72

I’m not going to be able to stream tonight. My Internet is down and the storms are still rolling through.

Raleigh-Durham Maker Meetup dates have been finalized for the rest of 2025! We love meeting makers of all ages, skill levels, and type! Bring your project or just your ideas and chat with other creators/makers!

Another Maker Meetup is underway! Come on down if you are in the Raleigh area, NC area.

No morning stream as I am down at @ecovate3d getting ready for the Maker Meetup! If you’re in the area then come down and join us for a day of hanging out and discussing our projects. I will stream later today to build my FRAKS kit.

🌙 Overnight = (OTTOeject + Printer) x2 🖨️ Anycubic Kobra S1 + Creality K1C ⚡ 2 OTTOejects, 5 plates, 24 hrs of combined nonstop printing 😴 We slept. 🧠 OTTOeject didn’t. ✅ Zero stress. Zero downtime. All done. Full results in video below 😁 #OTTOeject #3DPrinting #PrintFarm…

Sorry everyone. I just got home so no stream tonight. Will try for a stream tomorrow.

Chat, Chill, N' Build Stream | Mercury Rising Rebuild - Part 4 is upon us! Join me in 10-ish minutes as we build from the bottom up! Let's put a skirt on the Nebula Frame and transfer the electronics. twitch.tv/DigitalDragon72

Tonight’s stream will begin a little later than usual. I just left work.

It's almost time for Chat, Chill, N' Build Saturday! Grab some breakfast and coffee then join me in the Dragon Den for the ZeroG Mercury One.1 Rebuild project! We will focus on finishing up the Gantry and I'll show you the new parts that have arrived. twitch.tv/DigitalDragon72

Sorry folks, I will not be streaming tonight. Work had me tied up most of the day and I am mentally exhausted. We will stream Saturday morning and continue to work on the ZeroG Mercury rebuild project! See everyone this weekend.

Reminder: I will not be streaming tonight due to work commitments. Hopefully we will be back to building on Thursday night.

Polymaker Restock Day Sale is going on now with 35% savings! Head over and stock up now for all your summer/fall printing projects. You can use my affiliate link to also show some love and support for my Twitch channel. us.polymaker.com/?aff=386

While the streams this week were non existent, work for the Anycubic Mega X rebuild was! Was able to clean up the wiring for the new board and get everything back together! There is still work to do with the exterior wiring and the klipper config but it’s getting there!

Mrs Dragon is being very tolerant of the Voron Rehab I have going on in the Living Room. Hopefully most of these will be done this week.

Chat, Chill, N' Build Saturday is going to be delayed by a few minutes. Running behind and cleaning up after some failed overnight prints (which happened to be for today's stream). See everyone soon! 10:15-ish AM ET. twitch.tv/DigitalDragon72